



The AGC 150 ATS is a dedicated automatic transfer switch (ATS) controller capable of handling any type of power source. Its flexible setup options let you use it in a wide range of emergency power solutions by controlling up to three breakers. The IP65 certified front-mounted controller is easy to install, set up, and use.
Any power source in Source-Source mode
In addition to Generator-Mains mode (operating the ATS to switch between a mains incomer and a genset), the AGC 150 ATS can operate in Source-Source mode, accepting any kind of power source (for example two mains incomers, or a combination of mains or a genset with a battery energy storage system or a renewable power source). The controller can send start and stop signals to both sources.
Many operating options
The AGC 150 ATS uses automatic mains failure (AMF) logic and control signals defined by the controller’s input/output settings to operate the ATS. For example, it can monitor a mains source for voltage, frequency, and voltage anomalies, switching to the secondary source in case of issues (after sending a start signal and checking that the voltage from the secondary source is within the defined limits, if needed).
Flexible blackout prevention options
Designed for flexibility and efficient blackout prevention, the AGC 150 ATS includes an Overlap feature that prevents blackouts during source switching by keeping the breakers of both sources closed for a user-defined period and enabling short-time paralleling. You can prioritise sources using parameters or digital inputs, offline or online, and you can prioritise one of the connected sources, let the controller prioritise a source randomly, or prioritise both in a three-breaker setup.
Two or three breakers supported
The AGC 150 ATS can control two or three breakers, allowing you to open and close a bus tie breaker between the two power sources if needed. The controller can therefore be configured for use in virtually any ATS application, anywhere in the world, including the use of two sources simultaneously.
Easy setup and operation
You can easily configure the AGC 150 ATS for your application by adjusting its built-in parameters or by using the M-Logic feature in DEIF’s free USW-3 utility software. The sunlight readable LCD provides easy setup and quick access to important information. On-screen text can be displayed in 8 languages, and the illuminated buttons smoothly guide the operator and make the controller very easy and intuitive to operate.
Other AGC 150 variants
The AGC 150 ATS is part of DEIF’s AGC 150 series of controllers that is designed for OEMs and system designers and provides flexible solutions for a wide range of power and engine control applications. The series also includes the following:
The AGC 150 Generator contains all necessary functions for control and protection of a genset.
The AGC 150 Mains can synchronise one or two breakers (mains breaker and tie breaker) plus protect and monitor the utility.
The AGC 150 BTB can synchronise one breaker, protect and monitor the busbar. In total, DEIF’s power management system can handle eight bus tie breakers.
The AGC 150 Stand alone controls non-synchronising applications with all the necessary functions for genset protection. It stands out for its reliability and operator-friendliness.
The AGC 150 Hybrid comes with all the necessary functions for protection and control of a hybrid installation with PV and genset.
The AGC 150 Engine Drive provides engine protection and controls engine start and stop sequences, including fixed- and variable speed functions for pump applications.
The AGC 150 Remote Display provides access and control of any master controller in the AGC 150 series over the local network. This provides fast incident response and operational convenience.
The AGC 150 PMS Lite controller is ideal for setting up and operating simple power management systems in off-grid plants with up to 128 gensets.
Read more
Contact us to discuss your options
- 90 years of energy pioneering
- Manufactured at the highest standards
- Superior quality
- Unmatched service and support
- Made in Denmark

Advanced Genset Controller AGC 150 Hybrid
- Minimum Genset load
- Load calculation in terms of solar power
- Genset start/stop based on mains import/export
- Genset start/stop based on PV production
- PV included in mode: MPE Mains Power export/import
- PV included in mode: LTO Load Take over
- PV included in mode: Fixed Power
- PV included in mode: AMF Automatic Mains Failure
- PV included in mode: Peak Shaving

AGC 150 Engine Drive AGC 150 Engine Drive
- Engine start and stop sequences
- Monitor and protect the engine
- Mechanical and electrical controlled engines in one unit
- Pump function with both fixed and variable speed
- Auto and manual control of engine speed via Digital input, analogue input, buttons or communication
- Monitor pump functionalities flow, pressure and more
- Configuration warning or shutdown alarms
- Stage V / Tier4F complaint
- 3 level password protection
- Alarm and event log
- 11 languages
- Ethernet USB RS485
- Front panel sealed to IP65
- UL certification

Advanced Genset Controller AGC 150 BTB
AGC 150 BTB - features
- Automatic close of bus tie breaker if the system requests help
- Manual control of bus tie breaker
- Section management
- 12 Digital inputs and 12 digital outputs
- Communications ports (CAN, USB, RS485, Ethernet).
- Event & alarm log (500 each)
- Programmable PLC editor

Advanced Genset Controller AGC 150 Mains
AGC 150 Mains - features
Operating modes with single or multiple mains:
AMF, Fixed power, Mains power export Load take over, Peak shaving
- Mains (Utility)
- power monitoring (kW, kV, A & pf)
- decoupling protection
- kW export protection
- electrical protections
- No break transfer of load
- Multi start settings
- Minimum of starting genset
- 12 Digital inputs and 12 digital outputs
- Communications ports (CAN, USB, RS485, Ethernet).
- Event & Alarm log (500 each)
- Programmable PLC editor

Advanced Genset Controller AGC 150 Stand alone
- RS486
- PLC
- Inputs/ Outputs
- Analog Inputs / Analog Outputs
- Analog inputs support resistans, current and voltage
- AOP 2 support
- Emulation for easy training and FAT
- UL approved
- Automatic Mains Failure sequence
- Tier4 final / Stage V
- Emission control with force regeneration and SOOT alarm
- Fuel pump logic (after filler)
- Changable operation mode (multiple modes in one software)
- Adapting controls (Controllers shows only relevant buttons)
- Front mount
- DEIF digital AVR DVC550 support
- Additional I/O modules support (CANbus based CIO)
- Engine CANbus
- Engine and Generator protection
- -40 degree support
- Ethernet
- USW
- USB

Advanced Genset Controller AGC 150
- Synchronization
- Power Management Core (32dg)
- -40 degree support
- PLC
- Engine and Generator protection
- Engine CANbus
- Front mount
- Additional CANbus based I/O (9 x CIO modules)
- DEIF digital AVR DVC550 support
- Multi purpose PID´s
- Tier4 final/stage5
- Emulation
- Hybrid EMS support
- Fuel optimisation